Trenchless methods
Hydro jetting in Atlantic City
Sewer lines in Atlantic City fill with things a snake cannot remove: sand carried in by the tide, grease from a hundred kitchens along the boardwalk, and scale flaking off old cast iron. Hydro jetting scours the pipe wall with pressurized water and carries all of it to the main, and it is the cleaning step that comes before every liner.
Serving Atlantic City · Atlantic County
The Trenchless Team
CIPP Verified installer. Camera inspection before any quote; permits and inspections handled. More about The Trenchless Team →
What the jetter does
A hydro jetting unit is a high-pressure pump, a water tank and a long hose ending in a nozzle with jets angled backward. Water leaving the rear jets at pressures from roughly fifteen hundred to four thousand pounds per square inch propels the nozzle up the line and scours the wall behind it, and the debris is carried downstream to the main by the volume of water. Nozzles are swapped for the job: a flushing nozzle for sand and sediment, a rotating or spinning nozzle for grease, a chain or root-cutting head for intrusions at joints, and a descaling head for cast iron. The operator feeds the hose in from the cleanout and works it out and back until the camera that follows shows clean pipe.
Three jobs it does in Atlantic City
The first is sand. Tidal groundwater entering an island lateral through open joints carries fine sand that settles on the invert and builds a bar, and surge events like the one in 2012 left some lines a third full. A flushing nozzle lifts and carries the sand to the main in a way no cable can. The second is grease. The restaurants on the boardwalk, the kitchens inside the casino-hotels and the motels and condo buildings in Ventnor, Margate and Brigantine all run drains that grease narrows over a season, and a spinning nozzle with hot water strips it from the wall. The third is roots. Across the bay in the Pleasantville, Absecon, Galloway and Egg Harbor Township subdivisions, with drier ground and yards full of oak, pitch pine and bayberry, roots push into clay joints and into the seams of fiber pipe, and a cutting head removes them so the camera can see the joint they came through.
Jetting as preparation for lining
A cured liner bonds to the host pipe, and it will not bond to sand, grease or loose scale. Every lining and point repair job therefore begins with jetting, and on cast iron it continues with a chain flail until the camera sees bare metal under the tuberculation. The crew cleans, scopes, and cleans again if the first pass left deposits, and the final camera pass before the liner goes in is recorded so the owner can see the surface the resin will bond to. Jetting is also how branch connections and the locations of defects are made visible for measuring. The standards that describe what a host pipe must look like before lining are published at the CIPP reference.
Judgment before pressure
Jetting is not applied blindly. A camera look before the nozzle goes in tells the operator whether the pipe can take full pressure. A clay lateral in Atlantic City that has cracked through, a cast iron invert worn to a sliver, or a length of Orangeburg that has softened can be opened up by the same water that is meant to clean it. In those cases the operator lowers the pressure, uses a flushing rather than a cutting nozzle, or recommends skipping the cleaning and going straight to a burst, since there is nothing left worth cleaning. The owner is told which it is. the verified installer covering Atlantic City does the camera work and the jetting on the same visit for homes, restaurants and buildings across Atlantic County, and does not jet a lateral it has not looked at.
Maintenance schedules
- Residential laterals on the island with known infiltration: jetted as needed between backups until the joints are sealed, after which cleaning is rarely required.
- Mainland laterals with root history: jetted annually, or sealed with a liner so the roots have no entry.
- Restaurant and commercial kitchen drains: jetted quarterly or before each season, with the interceptor pumped first.
- Hotel and condo tower stacks and building drains: jetted on a planned cycle as part of a maintenance survey.
- Storm drains and culverts in the marina district and the low-lying areas: jetted after a surge or flood event and before the season.
Booking
Call (877) 739-3789 or send the form. An active backup is scheduled first and cleared, then scoped. Routine jetting for a commercial kitchen is booked for off hours. Installers vetted for other regions are listed at the verified installer directory.
Estimates are free. Call now: (877) 739-3789.
Other trenchless services in Atlantic City
Trenchless Sewer Repair Atlantic City
Repair or replace a failed sewer line with little or no excavation.
Sewer Pipe Lining (CIPP) Atlantic City
A resin-saturated liner cured in place forms a new, jointless pipe inside the old one.
Pipe Bursting Atlantic City
A bursting head splits the old pipe while pulling new HDPE pipe in behind it, through two small pits.
Sectional Point Repair Atlantic City
A short liner fixes one bad spot and leaves the rest of a sound line alone.
Sewer Camera Inspection Atlantic City
See what is actually wrong before anyone quotes a fix.
Sewer Line Repair & Replacement Atlantic City
When a line cannot be lined: spot excavation or trenchless replacement, chosen from the footage.
Questions we hear about hydro jetting
Can jetting damage an old lateral?+
It can finish off a pipe that was already failing, which is why the camera goes in first. On a lateral with a thin iron invert or clay that is cracked through, the pressure is reduced, the nozzle is chosen for flushing rather than cutting, or the cleaning is skipped in favor of going straight to repair.
Why does the sand keep coming back after jetting?+
Because the opening that admits it is still there. Jetting removes the sand bar but not the separated joint or the crack that the tide pushes sand through. The camera pass after jetting finds that opening, and a point repair or a liner closes it. Jetting alone on an island lateral is maintenance, not a cure.
How often should a restaurant line be jetted?+
Boardwalk and casino kitchens with heavy fryer use commonly jet their drains quarterly or before each season, in addition to pumping the grease interceptor. A lined drain holds less grease than rough iron and can go longer between cleanings. The installer can set a schedule after seeing the line.
Is jetting the same as snaking?+
No. A cable machine bores a hole through a blockage and leaves the rest of the deposit on the wall. A jetter removes the deposit from the full circumference of the pipe and flushes it downstream, which is why the line stays clear longer and why it is the only acceptable preparation for lining.
How do I get a price?+
Get in touch at (877) 739-3789 or through the form. A camera check comes first to confirm the pipe can take the pressure, the jetting is priced by the run, and a second camera pass afterward shows what the cleaning revealed. Estimates are free; call now.